Showing results: 691 - 705 of 862 items found.
-
Meco Instruments Pvt. Ltd.,
Basic Accuracy 0.25%Max. Test Current : 5A (120mV) for 7002Max. Test Current : 10A (60mV) for 7272Manual or Auto RangeFour Terminal Kelvin Measurement6 Ranges with 1mV Best ResolutionMeasurement of Resistive and Inductive MaterialsSetting for HI, LO & PASS ReadingsMemory of 3000 Measurements DataProgrammable HI-LO Alarm with memory of 20 DataLarge LCD with Backlight & HOLD FunctionLow Power ConsumptionBattery Operated with AC AdaptorLow Battery (Voltage) AlarmLED indication for Invalid Resistance MeasurementCable Length Measurement in feet & metersUser Interface Software for PC Communication via RS232C(to USB Bridge) cableBuilt-inBatery Chaging Circuit & Calender Clock
-
Power Monitoring and Diagnostic Technology Ltd.
PMDT is the only manufacturer to utilize all 5 types of online partial discharge sensor technology. Using multiple sensing methods ensures that PD activity is always discovered, located, and characterized. PMDT's handheld PDetector and PDStar units have more capability than the high-end diagnostic equipment of the past. The small handheld, battery powered unit can completely perform the test and analysis without the need of a PC. PDetector, PDStar, and PDiagnostic instruments feature high-resolution phase-resolved analysis of PD signals (PRPD and PRPS) in real time, so you get your test results instantly!
-
Wuhan Sunma Technology Co., Ltd.
The SunmaFiber SDH & Ethernet is easy to use, cost effective Ethernet testing solution for basic physical layer cable testing, layer 2 and layer 3 traffic generation, and full RFC 2544 testing. The rugged, battery operated, application specific test tool enables field technicians to turn-up Ethernet and IP services by running an RFC 2544 test or following a set of methods and procedures. The product has been designed for front-line technicians who do not have experience dealing with emerging Metro Ethernet technologies and need a simple to use solution for Ethernet and IP testing.
-
IT6900A Series -
I-TECH Electronic Co., Ltd
IT6900A series wide range programmable power supply have built-in standard RS232, USB, GPIB, RS485 and analog interface (RS485 and analog interface are just for IT6900B), support SCPI protocol, facilitate remote control, industrial PLC control and the formation of intelligent test platform. Remote compensation terminals avoid the problem of inaccurate testing caused by voltage drop on the wire.Low ripple, low noise and built-in digital voltmeter make IT6900A easy to do external measurement.IT6900A can be widely applied in DC-DC power supply module, battery charging and sensors and other test areas.
-
Extech EX503 -
Extech Instruments Corporation
The EX503 offers an array of must-have multimeter measurements including capacitance, frequency (dual sensitivity for electrical and electronic applications), diode test and continuity. Other features include Data Hold and Relative Hold, and manual- or auto-ranging modes. The latter automatically adjusts the measurement range based on the detected source such as electrical components and electronic equipment. The meter features 0.5 percent accuracy and a CAT IV-600-volt safety rating, protecting users even on outdoor wiring. Includes EX503 heavy-duty digital multimeter, double-molded test leads, magnetic hanging strap, 9-volt battery, carrying case, and user manual.
-
Extech EX411A -
Extech Instruments Corporation
The EX411A offers multiple functions so you can carry one meter into the field instead of several. The manual-ranging EX411A measures AC/DC voltage, AC/DC current, resistance, diode, and continuity, all with +/-0.5 percent basic accuracy. The unit has low current capability, measuring down to 0.1uA, and features input fuse protection and mis-connection warnings. A Type K thermometer is built in for surface or air temperature measurements. Comes with CAT III test leads, stand, hanging strap, holster with built-in test lead storage, Type K bead wire temperature probe, and battery.
-
RLB -
RARA Electronics Corporation
RARA manufactures load banks, ranging from small portable units for testing generators to multi-megawatt designs for larger applications. Regular load testing, along with correct battery maintenance, is the best way of ensuring the reliability of standby power systems. It is routine for all newly-installed generating sets to have a load test during the commissioning process in order to prove the performance of the set and all ancillaries-cooling system, exhaust system, switchgear and protection schemes.
-
Tester SA9083 -
JSD TestPhone Ltd
The Tester SA9083 is a battery powered, multi-range, analogue portable instrument. It is primarily intended for use by faultsmen for maintenance testing of telecommunication lines and equipment, subscriber installations connected to exchanges where faultsmen do not have access to a test desk, or where the testing equipment at the local exchange is not staffed during normal working hours. It has three input terminals, a range selector switch and a dual purpose push-button reversing switch (B-A changeover/test cell).
-
AUTO-OHM 10 -
Manta Test Systems
The Vanguard Auto-Ohm 10 is a 10-ampere battery powered micro-ohmmeter designed for low-resistance-measuring applications such as the measurement of resistance in circuit breaker contacts, bushing contact joints, and welding joints. The unit is powered by four 3400mAh, 3.7Vdc Li-Ion rechargeable batteries. With these high capacity batteries, up to 2,900 tests per charge (10A/2 second duration) can be performed in the field. The Auto-Ohm 10 features a built-in charger that can charge the batteries when the unit is not in use.
-
Otii Arc Pro -
Qoitech AB
Otii Arc Pro is an instrument that can precisely source voltage or current and simultaneously measure voltage and/or current. It computes power and energy and syncs with software output, enabling engineers and developers to easily see what drains the energy and optimize the battery life of their devices under test.
-
OT-9800 -
Radiantech, Inc.
FiberPal OT-9800 OTDR series is designed with ultra portable, light, reliable and easy to use as Fiber Quick test and Troubleshooter to locating fiber connector, break and imperfections for FTTX, CATV and optical LANs. FiberPal OT-9800 OTDR series detects event locations along the optical fiber and displays the results on a portable device like notebook, Tablet PC and Mobiles phones with Android 4.x operation system. OT-9800 is with internal battery and Bluetooth function.
-
Extech UM200 -
Extech Instruments Corporation
The Extech UM200 is a precision Micro-Ohm Meter which features a resolution down to 1 µΩ. The UM200 has 6 ranges with 3 sub-ranges in each current range. It features a 5-Digit backlit LCD, PC interface, auto or manual ranging, and a 10 A maximum test current. Store/Recall up to 3000 measurements. Complete with 4-wire cables with Kelvin clip connectors, rechargeable Li-Polymer battery, AC adapter/charger, software and USB cable, and soft carrying case.
-
695 -
Electronic Specialties Inc.
Great tool for accurate measurement of low current. Use with your graphing meter or lab scope to view current waveforms on fuel injectors, fuel pumps, primary ignition coils and more. Also works very well with digital multimeters. Resolution of 10 milliamps is low enough for most parasitic drain testing. In addition, the clamp opening of 1/2 inch is large enough to clamp over most negative battery cables for those parasitic drain tests.
-
165 CB -
Standard Electric Works Co., Ltd
● 165 CB is an ideal tool which can test the correct pin configuration for different kinds of cables.● For testing: -RJ45/RJ11 -USB -COAX -BNC cable -Multi-wire cable● Auto-scan and manual-check function● Buzzer sound warning for wire status● 2 LED module indicators on the master unit which can do both of transmitter and receiver functions for RJ45/RJ11 cable testing. Users don't need to use the receiving unit.● 165 CB provides a variety for checking cable continuity, open status, short status and miss-wired. ● Ground (shielded ) wire test.● LED indication for wire status.● Power source : 9V battery
-
781155-01 -
NI
2-Channel, 8 V, ±3 A PXI Programmable Power Supply—The PXIe‑4154 is a specialized programmable power supply for battery simulation. It is designed to simulate a lithium‑ion battery cell’s transient speed, output resistance, and 2‑quadrant operation (source/sink). Critical to many RF and wireless applications, the simulator’s fast transient response time allows it to rapidly respond to changes in load current with minimal voltage dip, which makes the PXIe‑4154 ideal for powering devices under test (DUTs) such as RF power amplifiers, cellular handsets, and a variety of other mobile devices. To model the behavior of a battery more accurately, you can use the onboard programmable output resistance to simulate a battery’s internal resistance. For quiescent and standby current measurements, the PXIe‑4154 features integrated current measurement.
